
We supply motor, frame, flight controller and gimbal screws to DIN, ISO and JIS standards or to your drawing, in SCM435 alloy steel and stainless steel chosen for strength, weight and corrosion resistance.
For motor mounts and arm joints we would suggest SCM435, a chromium-molybdenum steel heat treated to property class 10.9 or 12.9 (minimum tensile strength 1,040 or 1,220 MPa, about 151,000 or 177,000 psi) that keeps its toughness under motor vibration. We make SCM435 screws from M1.2 upward, covering the M2, M2.5 and M3 sizes common on multirotors.
Vibration is a common cause of loosening, so we supply drone screws with pre-applied thread lock, from reusable Nylok nylon patches to Precote microencapsulated coatings. DIN 267-27 covers these coatings from M3 to M39 only, so for M2 and M2.5 screws we would suggest agreeing the coating and test method in writing.
Please see our screw specifications page for the full range. For drone screws we also offer SCM435 in class 10.9 and 12.9, with clear zinc or electroless nickel plating (ENP)
Choose based on the product’s intended use, application method, and customer requirements.
Commonly used types include SUS302, SUS304, SUS316, SUS410. A special type called NSSC550 is exclusive to Cheng Hao, which has high hardness, high corrosion resistance, and high acid resistance. Its rust prevention is 15 times better than existing materials for screws.
Low carbon steel, medium carbon steel, high carbon steel.
Refers to steel materials that, besides containing carbon, also have other alloying elements such as silicon, manganese, chromium, nickel, vanadium, molybdenum, etc.
Common material codes include 2011, 2024, 6061, 6082, 7075.
Brass (Yellow brass), Bronze.
Choose based on the product’s intended use, application method, and customer requirements.
We machine custom parts in-house on CNC equipment and produce cold-formed screws through managed partner factories, so we can quote machined standoffs alongside the screws. We sample custom parts for your approval before mass production, and every delivery carries an inspection certificate.
Motor mount screw length needs care, since a screw that runs too deep can reach the stator windings and short the motor, as the NXP HoverGames assembly guide warns. We would suggest marking the maximum length as a critical dimension on your drawing.

These are some of the most frequently asked questions by our customers. We hope they are helpful to you. If you cannot find the answer you need, please contact us using the inquiry button below.
Cheng Hao makes SCM435 alloy steel drone screws from M1.2 upward, and smaller micro screws in SUS304 and SUS316 for cameras, sensors and circuit boards. Typical drone specifications include M2 × 0.4 × 5 mm (0.20 in) socket head, M2.5 × 0.45 × 8 mm (0.31 in) button head and M3 × 0.5 × 8 mm flanged button head screws with a T8 Torx drive. We produce to DIN, ISO, JIS, BSW, IFI and UTS callouts, and non-standard sizes and head forms can be made to your drawing.
SCM435 is a chromium-molybdenum steel that Cheng Hao supplies heat treated to property class 10.9 or 12.9, with a minimum tensile strength of 1,040 or 1,220 MPa. The alloy holds its toughness under the fatigue loading that motor vibration produces, and its hardened drive resists cam-out during automated assembly. A 7075 aluminum screw has a little under half the strength of a class 12.9 SCM435 screw, so for motor mounts and arm joints we would suggest SCM435.
For carbon fiber drone frames we would suggest SUS304 or SUS316 stainless steel screws where the load allows. A 1985 NASA conference paper on fasteners for advanced composite materials by R. C. Landt lists aluminum alloys and alloy steels as not compatible with graphite fiber composites, while 304 and 316 stainless steel are accepted, usually installed with sealant.
Where an SCM435 screw is needed for strength, please discuss the finish and joint sealing with Cheng Hao before approving samples.
Acid cleaning and zinc plating introduce hydrogen into the steel, and in screws of class 10.9 and above that hydrogen can cause a fracture some time after the screw has been tightened.
Cheng Hao’s zinc-plated high-strength screws are baked immediately after plating to relieve this risk, and ISO 4042 sets out the measures for electroplated fasteners. Please state the baking requirement on your drawing if your program specifies one.
Cheng Hao supplies drone screws with pre-applied thread lock. Nylok nylon patches can be reinstalled several times and work to around 121°C (250°F), Precote 85 microencapsulated adhesive gives a high breakaway torque for joints that stay assembled, and Precote 50-TF combines locking with a controlled friction coefficient for automated screwdriving. For M2 and M2.5 screws, which fall outside DIN 267-27, we would suggest agreeing the coating and the test method with us in writing.
The motor mount screw should be long enough to engage the motor’s threads fully but short enough to stay clear of the stator windings, which a long screw can reach and short. The correct length depends on the arm thickness and the motor’s thread depth, so please give us both, or mark the maximum length as a critical dimension on your drawing. We confirm it on the sample batch before mass production.
Agricultural spray drones expose their fasteners to fertilizers, pesticides and frequent washing, so we would usually suggest SUS316 stainless steel, which has high corrosion and acid resistance.
Where SCM435 is needed for strength, electroless nickel plating is worth considering as the finish. Chemical mixes vary considerably, and we would recommend testing samples against the products you actually spray before approving a material.
Cheng Hao’s minimum order quantity for standard screws is 50,000 pieces in stainless steel and 100,000 pieces in carbon steel. For special-purpose screws, or orders with a high total quantity, we can accept a lower minimum. CNC machined parts such as standoffs are quoted per part.
Cheng Hao delivers custom drone screws in 30 to 75 days, depending on quantity, material, finishing and thread lock coating. Some standard specifications are held in stock. For custom parts we produce a small sample batch for your approval before mass production begins.
Cheng Hao’s quality management system is certified to ISO 9001, and some products carry CE marking. Every delivery includes an inspection certificate. If your program requires AS9100 documentation, or vibration testing of the locked joint to ISO 16130, please raise it at the inquiry stage so that we can confirm what we are able to provide.
| Service | Cookies | Description |
|---|---|---|
| Google Analytics | _gat_gtag, _ga, _gid | Used to distinguish users and sessions for web statistics purposes. |
| Service | Cookies | Description | |
|---|---|---|---|
| Google Analytics | _gat_gtag, _ga, _gid | Used to distinguish users and sessions for web statistics purposes. |